Finding your suitable readers for antminer s9 cooling is not easy. You may need consider between hundred or thousand products from many store. In this article, we make a short list of the best readers for antminer s9 cooling including detail information and customer reviews. Let’s find out which is your favorite one.
817 reviews analysed
1. Asicminer Fan for Antminer S3, S5, S5+, S7, S9 D3, L3
Description
Fans for AntMiner S3, S5, S5+, S7, S9, L3, D3. The length of wire is 24cm. DC12V 2A
2. Fan Simulator for BITMAIN Antminer S9 S11 S15 S17 D3 L3+A3 T9 Z9 E3 | Direct Plug & Play Emulators | Oil Submersion 3M Novec | Fully Assembled Fake Fan Sensor, Eliminator, Fan Delete, Spoofer (2 Pack)
Feature
- ✔MOST EFFICIENT BITMAIN FAN SIMULATOR IN 2019✔ This is the most efficient little device you can use to emulate the cooler fan presence and make the ASIC think that the fan is running perfectly. You can completely remove the fans if you are cooling your device with oil submersion as they won’t be required in the cooling system. It’s a neat device with an expert product finesse & we are sure you are going to enjoy adding this to your Bitcoin mining hardware kit.
- ✔EASY PLUG & PLAY INSTALLATION✔ It is a simple plug-and-play device with no programming required & does not need any configuration as well. It allows the miner to run without any errors by sending a fan sense, a tachometer signal, to the miner’s controller tricking & making the it believe that it has fans attached and working within parameters. Each Antminer cooling fan requires 1 emulator & PCB plugs directly into the primary fan port. It’s as simple as that!
- ✔OIL IMMERSION & CALIBERATION✔ Bitcoin/Crypto miners like the Antminer S15, S11, S9, S7, S5 & they know very well that having an effective cooling system is essential for their success. Immersed either in a dielectric oil or 3M Novec ensures a cooler environment & stable system performance. Fan can run at full speed & also the RPM can be adjusted (variable) at any time. The device typically reports fan speeds around 6000-8000 RPM which is good enough for an Antminer S9/D3/L3+ etc.
- ✔HIGH QUALITY COMPONENTS & POWER CONSUMPTION✔ Our package will include 2 emulators, they are horizontally oriented & come with insulated power cord/Antminer cable. The printed circuit board undergoes a transport stability test and a final 1 hour performance test to ensure product quality. With 12 V & 0.09 W power, it consumes extremely less amount of power to operate which is far less than a fan. This is suitable for Bitcoin Mining Machines, Mining Rigs or other devices that use 4pin connectors.
- ✔MONEY BACK PRODUCT WARRANTY✔ It is a fully compliant & backed up by manufacturer’s warranty so feel free to contact us for any query or information. We have a track record of ensuring happiness of clients and are absolutely confident that our product will exceed your expectations. Just in case the product falls short of your expectations in any manner, you can return it for a 100% refund. We will go an extra mile to redress the situation at hand.
Description
Our product acts as an Antminer cooler by replacing the Bitmain Antminer’s fan and provides a tach signal to the Antminer Control Board/Antminer Power Supply. Simply unplug the fans and plug in the fan emulator. The Antminer now starts thinking that it has control over fans that do not exist. This can be used for other applications that use high RPM (6000+), pulse width modulated (4-wire) fans. Our device is designed specifically for Antminers by a team of specialist engineers with high quality, professionally masked printed circuit board to meet the updated requirements as per user demand. You can completely remove the fans if you are cooling your device with oil submersion, so need to worry about having a fan shroud or a fan duct. The device also allows you to install low noise fans if you have very cold temperatures or are underclocking your miner/bitminer.
We do not compromise on product quality & always keep it as our first priority. We have a remarkable after sales service & provide a free product replacement warranty. If you are not satisfied for any reason, within the first 30 days, return it for a full 100% refund
We are absolutely confident that this product just like others will not disappoint you and will exceed expectations. Feel free to contact in case of any issue or further information.
3. Antminer S9 T9 L3+ E3 X 3 D3 120mm Fan Duct Cooling Shroud to 4 Inch Vent Hose (10 Pack)
Description
This vent shroud is designed to be directly mounted to 120mm cooling fans, as found on the AntMiner miner models S15, T15, X3, E3, S9, T9, L3, D3, A3 and others. Mounting the shroud to your AntMiner allows you to ventilate or cool your miner with a standard 4 inch dryer vent duct. Removing hot air from your AntMiners environment is one of the most important and easiest ways to keep your mining equipment cool and operating efficiently! This shroud will mount to your AntMiner with the existing screws. There is no need to purchase longer screws as required with other shrouds. This shroud also includes ridges on the 4″ inch connection port to ensure proper clamping of exhaust hoses to prevent leaking and hoses being accidentally detached. These ridges are not present on other shroud models available. A hose clamp is included with each shroud. This shroud can be used as an intake to direct cooler external air to your miner or as an exhaust to remove the hot air from our miner to another area. This is a custom engineered vent shroud brought to you by the team at ArcMyn. Compare our quality to other shrouds and you will find no comparison. Our shrouds are made from high temperature resistant injection molded ABS plastic that can withstand temperatures up to 221 degrees F (105 degrees C)! BEWARE listings that do not specify ABS plastic! Competitors use PLA plastic that will begin to melt and deform at 140 degrees F (60 degrees C)! We have observed miners increasing intake air temperature by over 40 degrees F! These temperatures can easily deform PLA printed shrouds causing exhaust blockages and over-heating! Don’t risk your expensive equipment with inferior products!
4. 6500 RPM Fan for AntMiner D3/L3+/S9/T9/S7/X3/Z9 AsicMiner Misieren BRUSHLESS SHLF1212GHE-07, V12E12BS1B5-07
5. Antminer S1 S3 S5 S7 S9 T9 L3+ 120mm Fan Duct Cooling Shroud to 4 Inch Vent Hose (15)
Description
Antminer S1 S3 S5 S7 S9 T9 L3+ 120mm Fan Duct Cooling Shroud to 4 Inch Vent Hose Extra thick for overclocking made in the USA fits Bitmain – S9, S9I, S9J, L3+, L3++, D3, A3, X3, E3, Z9, Z9 mini, E3, V9, S7, S1, T9, T1, X11, D9, S3, B3, S9 Innosilicon – A4, A4+, A8+, S11, A9, A5, 2X, T2, A2, D9 Dominator, Siamaster, Dashmaster, DecredMaster, ZMaster Dragonmint –D9, B29, T1, 16T,
6. Replacement Bitmain Fan for Antminer S9, T9, Z9, D3, E3, X3, L3+
Description
Replacement fan for Btimain AntMiner S9, T9, Z9, E3, X3, D3, L3++ and other series.
The length of wire is 24cm.
Does not include screws.
7. I-Miners Cooler Fan Simulator Emulator for Antminer S9 S11 S15 S17 D3 L3+ A3 T9 T15 T17 Z9 Z11 E3 DR5 E3 Oil 3M Novec (Pack of 10)
Description
Designed to trick any Bitmain Antminer Fan (or server/other device) into spinning at full speed.
8. Replacement Bitmain Fan for Antminer S3, S5, S5+, S7
Description
Fan only. Does not include metal protector or screws.
Conclusion
By our suggestions above, we hope that you can found Antminer S9 Cooling for you.Please don’t forget to share your experience by comment in this post. Thank you!
